Res. Agr. Eng., 2006, 52(1):30-37 | DOI: 10.17221/4877-RAE

Evaluation of factors influencing adhesive bond strength

M. Müller1, P. Hrabě1, R. Chotěborský1, D. Herák2
1 Department of Material and Engineering Technologies, Technical Faculty, Czech University of Agriculture in Prague, Prague, Czech Republic
2 Department of Mechanics and Engineering, Technical Faculty, Czech University of Agriculture in Prague, Prague, Czech Republic

In the last ten years periods the bonding technology noted a great boom not only in manufacturing industry but in repairing industry, too. The expansion of chemical industry is the cause of this boom. In this way the use of bonding technology in industrial applications brings considerable cost savings. For the successful use of adhesives the knowledge of used adhesives and of further affecting factors is important. Respecting of this know-how is the presumption of the bonded joint successful design. The breaking of the technological procedure and the incorrect design are very often reasons of wrong joints. The paper contains theoretical in formation about the bonded joints creation and some results of laboratory tests inquiring into the reasons which affect the bonded joint strength. For tests the two-component epoxy adhesives were used.

Keywords: bonding; bonding technology; surface preparation; testing of adhesive bonds

Published: March 31, 2006  Show citation

ACS AIP APA ASA Harvard Chicago Chicago Notes IEEE ISO690 MLA NLM Turabian Vancouver
Müller M, Hrabě P, Chotěborský R, Herák D. Evaluation of factors influencing adhesive bond strength. Res. Agr. Eng. 2006;52(1):30-37. doi: 10.17221/4877-RAE.
Share...
Download citation
  • BibTeX (.bib)
  • Bookends (.ris)
  • EasyBib (.ris)
  • EndNote (.enw)
  • EndNote 8 (.xml)
  • ISI WoS (.isi)
  • Medlars (.medlars)
  • Mendeley (.ris)
  • MODS (.xml)
  • Papers (.ris)
  • RefWorks (.txt)
  • RefManager (.ris)
  • RIS (.ris)
  • MS Word (.xml)
  • Zotero (.ris)
    • Open full article

    References

    1. Cagle Ch.V. (1973): Handbook of adhesive bonding. MacGraw-Hill, New York.
    2. ČSN EN 1465 (1997): Lepidla - Stanovení smykové pevnosti v tahu tuhých adherendů na přeplátovaných tělesech. Český normalizační institut, Praha.
    3. ČSN ISO 8486 - 1 (1996): Pojená brusiva - Stanovení a označování zrnitostního složení. Český normalizační institut, Praha.
    4. FIRM LITERATURE - LEPOX, UHU, BISON, ZTRADE.
    5. Habenicht G. (2002): Kleben: Gundlagen, Technologien, Anwendung. Springer, Berlin. Go to original source...
    6. ISO 4287 (1999): Geometrické požadavky na výrobky (GPS). Český normalizační institut, Praha.
    7. Kovačič L. (1984): Lepenie kovov a plastov. Alfa, Bratislava.
    8. Loctite (1998): Der Loctite. Worldwide Design Handbook. Loctite European Group, München.
    9. Peterka J. (1980): Lepení konstrukčních materiálů ve strojírenství. SNTL, Praha.
    10. Pizzi A., Mittal K.L. (2003): Handbook of adhesive technology. Dekker, New York. Go to original source...
    11. Ptáček L. (2001): Nauka o materiálu I. Akademické nakladatelství CERM, Brno.

    This is an open access article distributed under the terms of the Creative Commons Attribution-NonCommercial 4.0 International (CC BY NC 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.


    Return to the content