Res. Agr. Eng., 2007, 53(2):67-74 | DOI: 10.17221/2120-RAE

Technological and constructional aspects affecting bonded joints

M. Müller1, R. Chotěborský1, J. Krmela2
1 Department of Material and Engineering Technologies, Faculty of Technology , Czech University of Life Sciences in Prague, Prague, Czech Republic
2 Faculty of Production Technology and Management, J.E. Purkyně University in Ústí nad Labem, Ústí nad Labem, Czech Republic

Adhesive bonding is one of many materials connecting methods. In the last ten years periods the bonding technology noted a boom almost in all industrial branches. The use of bonding technology in the engineering and repairing industry brings considerable savings. Saving in costs, in critical metallic materials and in time are reached and the decrease of the joint weight, too. Therefore the bonding technology pertains to the modern jointing methods even though it is a very old technique. The adhesive bonding technology is influenced by a number of factors which affect the adhesive bond strength. Correcting coefficients have to be considered in construction calculations too. The correcting coefficients correct the strength deviations caused by particular factors. In the paper there are published laboratory experiments results.

Keywords: bonding technology; construction; corrective coefficients; testing of adhesive bonds

Published: June 30, 2007  Show citation

ACS AIP APA ASA Harvard Chicago Chicago Notes IEEE ISO690 MLA NLM Turabian Vancouver
Müller M, Chotěborský R, Krmela J. Technological and constructional aspects affecting bonded joints. Res. Agr. Eng. 2007;53(2):67-74. doi: 10.17221/2120-RAE.
Share...
Download citation
  • BibTeX (.bib)
  • Bookends (.ris)
  • EasyBib (.ris)
  • EndNote (.enw)
  • EndNote 8 (.xml)
  • ISI WoS (.isi)
  • Medlars (.medlars)
  • Mendeley (.ris)
  • MODS (.xml)
  • Papers (.ris)
  • RefWorks (.txt)
  • RefManager (.ris)
  • RIS (.ris)
  • MS Word (.xml)
  • Zotero (.ris)
    • Open full article

    References

    1. ČSN EN 1465 (1997): Lepidla - Stanovení smykové pevnosti v tahu tuhých adherendů na přeplátovaných tělesech. Český normalizační institut, Praha.
    2. FIRM MATERIAS - ALTECO, BISON, UHU.
    3. Habenicht G. (2002): Kleben: Grundlagen, Technologien, Anwendung. Springer, Berlin. Go to original source...
    4. Herák D., Chotěborský R., Müller M., Hrabě P. (2005): Bonded wooden balks. Research in Agricultural Engineering, 51: 145-151. Go to original source...
    5. Kříž R., Vávra P. (1994): Strojírenská příručka. Sv. 5. Scientia, Praha.
    6. Loctite (1998): Der Loctite. Worldwide Design Handbook. Loctite European Group, München.
    7. Macháček O., Majer F. (1981): Statistika II. SPN, Praha.
    8. Müller M., Hrabě P., Chotěborský R., Herák D. (2006): Evaluation of factors influencing adhesive bond strength. Research in Agricultural Engineering, 52: 30-37. Go to original source...
    9. Peterka J.(1980): Lepení konstrukčních materiálů ve strojírenství. SNTL, Praha.
    10. Reis P. (1998): Worldwide design handbook. Erasmusdruck Gmbh, Munchen.
    11. Sadek M. (1987): Industrial application of adhesive bonding. Elsevier Applied Sciency, London. Go to original source...

    This is an open access article distributed under the terms of the Creative Commons Attribution-NonCommercial 4.0 International (CC BY NC 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.


    Return to the content