Res. Agr. Eng., 2011, 57(10):S61-S68 | DOI: 10.17221/21/2011-RAE

Material machining for friction knots of moving parts for agricultural machines

J. Žitňanský, J. Žarnovský, R. Mikuš, I. Kováč, Z. Andrássyová
Faculty of Engineering, Slovak University of Agriculture in Nitra, Nitra, Slovak Republic

The study deals with the effect of the cutting parameters such as the cutting speed, feed and cooling on the quality of machined surfaces in the process of hole drilling for the sliding bearings used in agricultural technique. This effect has been studied on various metals such as copper, brass, dural and leaded bronze, which are commonly used for their friction knots of the moving parts for agricultural machinery. The results suggest the use in the design of collection parts, scything strips, as well as lifting equipment of agricultural technique, where particular linear and rotary movements of the friction parts are slow, as well as for the design of appropriate drilling procedures.

Keywords: friction knot; sliding bearing; cutting speed; cooling; quality of machined surfaces

Published: December 31, 2011  Show citation

ACS AIP APA ASA Harvard Chicago Chicago Notes IEEE ISO690 MLA NLM Turabian Vancouver
Žitňanský J, Žarnovský J, Mikuš R, Kováč I, Andrássyová Z. Material machining for friction knots of moving parts for agricultural machines. Res. Agr. Eng. 2011;57(Special Issue):S61-68. doi: 10.17221/21/2011-RAE.
Download citation

References

  1. Anonymous, 2003. Iljin Machinery Co., Ltd. Available at http://www.iljin-mc.co.kr/english/technology/quality.htm?qt=surface (accessed February 03, 2010).
  2. Anonymous, 2007. Dimar Slovakia, Ltd. Available at http://mtf.dattex.net/modules.php?name=Downloads&d_op=getit&lid=28 (accessed April 25, 2009).
  3. Audy J., 2008. A study of dry machining performance of the TiN, Ti (Al,N) and Ti (C,N) coatings and a type M35 HSS tool substrate material assessed through basic cutting quantities generated when orthogonal turning a Bisalloy 360 grade steel work-piece material. Annals of Faculty Engineering Hunedoara - International Journal of Engineering, 6: 59.
  4. Audy J., 2009. Study of coatings on experimental thrust and torque in drilling. Annals of Faculty Engineering Hunedoara - International Journal of Engineering, 7: 31-40.
  5. Bátora B., Vasilko K., 2000. Obrobené povrchy (Cutting Surfaces). Trenčín, GC - Tech 2000, Inc.: 131.
  6. Ružbarský J., Tomáš J., 2006. Some results of the turning of hardened steel without cooling. Acta Avionica, 8: 87-90.
  7. Stephenson D.A., Agapiou J.S., 2006. Metal Cutting Theory and Practice. Boca Raton, CRC Press.
  8. STN 22 1140, 1977. Vrtáky skrutkové s kužeľovou stopkou. Základné rozmery (Taper shank twist drills. Basic dimensions).
  9. Unticell, 2007. Untilcell. Available at http://www.utilcell. com (accessed Fabruary 10, 2010).
  10. Žitňanský J., Kročko V., 2001. Vplyv podmienok dokončovania predvŕtaných dier na kvalitu vŕtaného povrchu a rozmerovú presnosť (Influence of drilled holes finishing conditions on drilling surface quality and accuracy of size). In: 6th International Scientific Symposium - Quality and Reliability of Machines. Nitra, SPU in Nitra: 101.
  11. Žitňanský J., Žarnovský J., 2010. Effects of material and cutting conditions on the temperature of drilling measured by thermovision technics. Manufacturing Engineering, 9: 34.

This is an open access article distributed under the terms of the Creative Commons Attribution-NonCommercial 4.0 International (CC BY NC 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.