Res. Agr. Eng., 2011, 57(10):S74-S78 | DOI: 10.17221/56/2010-RAE

Analysis of wear resistent weld materials in laboratory conditions

M. Kotus1, Z. Andrássyová1, P. Čičo1, J. Fries2, P. Hrabě3
1 Faculty of Engineering, Slovak University of Agriculture in Nitra, Nitra, Slovak Republic
2 Faculty of Mechanical Engineering, Technical University of Ostrava, Ostrava, Czech Republic
3 Faculty of Engineering, Czech University of Life Sciences Prague, Prague, Czech Republic

The aim of the study was the evaluation of the suitability of using filler surfacing materials in abrasion resistant layers according to their material and tribology features. Laboratory analysis of the selected materials consisted of the tests of hardness, microstructure and wear resistance determination. The abrasive wear resistance was defined according to the standard STN 01 5084. On the basis of the results obtained, we can state that using the hard-facing for the background is tenable for the purpose of wear amount decrement where the abrasive wear prevails.

Keywords: abrasive wear; relative resistance; laboratory analysis; abrasion resistant layers; Fluxofilcord 58; Fluxofilcord 59

Published: December 31, 2011  Show citation

ACS AIP APA ASA Harvard Chicago Chicago Notes IEEE ISO690 MLA NLM Turabian Vancouver
Kotus M, Andrássyová Z, Čičo P, Fries J, Hrabě P. Analysis of wear resistent weld materials in laboratory conditions. Res. Agr. Eng. 2011;57(Special Issue):S74-78. doi: 10.17221/56/2010-RAE.
Share...
Download citation
  • BibTeX (.bib)
  • Bookends (.ris)
  • EasyBib (.ris)
  • EndNote (.enw)
  • EndNote 8 (.xml)
  • ISI WoS (.isi)
  • Medlars (.medlars)
  • Mendeley (.ris)
  • MODS (.xml)
  • Papers (.ris)
  • RefWorks (.txt)
  • RefManager (.ris)
  • RIS (.ris)
  • MS Word (.xml)
  • Zotero (.ris)
    • Open full article

    References

    1. Balla J., 1989. Tribológia a tribotechnika (Tribology and Tribotechnics). Nitra, SUA in Nitra: 134.
    2. ČSN EN ISO 4063, 2011. Svařování a příbuzné procesy - Přehled metod a jejich číslování (Welding and allied processes - Nomenclature of processes and reference numbers).
    3. Hrabě, P., Chotěborský, R. 2005. Zvyšování životnosti abrazivně opotřebených strojních častí (Life Cycle Increasing of Abrasive Wear Machine Tools). MM Průmyslové spektrum, 5: 80-81.
    4. Kotus M. 2007. Aplikácia pulzných zváracích zdrojov pri renovácií súčiastok poľnohospodárskych strojov (Application of Pulse Welding Aggregates in Machine Parts Renovation of Agricultural Machines). [Ph.D. Thesis.] Nitra, SUA in Nitra: 201.
    5. Kotus, M. 2009. Tribologické skúšky oteruvzdorných materiálov (Tribological tests of abrasive resistant materials). In: Safety - Quality - Reliability. Košice, The Technical University of Košice: 103-107.
    6. Kotus M., Drahoš Š., 2010. Stanovenie odolnosti proti abrazívnemu opotrebeniu v laboratórnych podmienkach (Determination of abrasive wear resistance in laboratory conditions). In: Quality and Reliability of Technical Systems. Nitra, SUA in Nitra.
    7. STN 01 5084, 1973. Stanovenie odolnosti kovových materiálov proti abrazívnemu opotrebeniu na brúsnom plátne (Determination of metal material resistante against wear by abrasiva cloth).
    8. STN 41 2014, 1993. Ocel 12 014 (Steel 12 014). Go to original source...
    9. STN ISO 6507-1, 2006. Kovové materiály. Vickersova skúška tvrdosti. Časť 1: Skúšobná metóda (ISO 6507-1: 2005) [Metallic materials. Vickers hardness test. Part 1: Test method (ISO 6507-1:2005)].
    10. Tolnai R., Čičo P., 2002. Výber oteruvzdorných materiálov pre špecifické podmienky degradačných procesov (Selection of abrasive wear materials for specific conditions of degradable processes). Acta Mechanica Slovaca, 6: 167-170.

    This is an open access article distributed under the terms of the Creative Commons Attribution-NonCommercial 4.0 International (CC BY NC 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.


    Return to the content