Res. Agr. Eng., 2014, 60(10):S98-S103 | DOI: 10.17221/59/2012-RAE

Verification of the working life of a ploughshare renovated by surfacing and remelting in the operationOriginal Paper

I. Kováč, N. Vanko, M. Vysočanská
Department of Quality and Engineering Technologies, Faculty of Engineering, Slovak University of Agriculture in Nitra, Nitra, Slovak Republic

The most common way of renovation of the working parts of agricultural machinery is surfacing by hardfacing coated electrodes and piped hardfacing wires. Another way to prolong the working life of the machinery is the chemical heat treatment of the material surface by nitriding. By nitriding, high hardness is obtained of the surface affected by a suitable environment and by raised temperature. This paper deals with the possibilities of increasing the lifetime of the functional area of a ploughshare by the surfacing piped wire and hardfacing electrodes and reshaping the surface layer in an argon and nitrogen environment by using a welding rectifier and the Tungsten Inert GAS method, and by validation of these methods of renovation in operating conditions.

Keywords: equipment wear; renovation; weld deposit; saturation; soil processing tool

Published: December 31, 2014  Show citation

ACS AIP APA ASA Harvard Chicago Chicago Notes IEEE ISO690 MLA NLM Turabian Vancouver
Kováč I, Vanko N, Vysočanská M. Verification of the working life of a ploughshare renovated by surfacing and remelting in the operation. Res. Agr. Eng. 2014;60(Special Issue):S98-103. doi: 10.17221/59/2012-RAE.
Share...
Download citation
  • BibTeX (.bib)
  • Bookends (.ris)
  • EasyBib (.ris)
  • EndNote (.enw)
  • EndNote 8 (.xml)
  • ISI WoS (.isi)
  • Medlars (.medlars)
  • Mendeley (.ris)
  • MODS (.xml)
  • Papers (.ris)
  • RefWorks (.txt)
  • RefManager (.ris)
  • RIS (.ris)
  • MS Word (.xml)
  • Zotero (.ris)
    • Open full article

    References

    1. Čičo P., Bujna M., 2011. Odolnosť tvrdonávarových materiálov v prevádzkových podmienkach. [Wear Resistance of Hardfacing Materials in Operating Conditions.] Nitra, SUA in Nitra: 119.
    2. Daňko M., Čičo P., Kotus M., Pauliček T., 2011. Odolnosť materiálov vytvorených laserovým naváraním proti abrazívnemu opotrebeniu. [Abrasive wear resistance of materials produced by laser deposit welding.] In: Proceedings Quality and Reliability of Technical Systems, 16. Nitra, SUA in Nitra: 101-105.
    3. Chotěborský R., Hrabě P., Müller M., Savková J., Jirka M., Navrátilová M., 2009a. Effect of abrasive particle size on abrasive wear of hardfacing alloys. Research in Agricultural Engineering, 55: 101-113. Go to original source...
    4. Chotěborský R., Hrabě P., Müller M., Válek R., Savková J., Jirka M., 2009b. Effect of carbide size in harfacing on abrasive wear. Research in Agricultural Engineering, 55: 149-158. Go to original source...
    5. Kotus M., Čičo P., 2011. Vplyv parametrov MIG/MAG navárania na tvorbu návaru. [Effect of MIG/MAG Parameters by Surfacing on the Creation of Weld.] Nitra, Slovak University of Agriculture: 112.
    6. Kotus M., Andrássyová Z., Čičo P., Fries J., Hrabě P., 2011. Analysis of wear resistent weld materials in laboratory conditions. Research in Agricultural Engineering, 57 (Special Issue): S74-S78. Go to original source...
    7. Kollárová K., Simoník J., Švarda R., Žitňák M., 2007. Soil moisture as a surrogate factor to characterize the variability of soil conditions in precision farming system. In: Proceedings from Advances in Labour and Machinery Management for a Profitable Agriculture and Forestry - XXXII CIOSTA-CIGR section V, September 17-19, 2007. Nitra, Slovak University of Agriculture: 389-399.
    8. Kovaříková I., Šimeková B., Hodúlová E., Ulrich K., 2011. Properties of composite wear resistant layers created by laser beam. In: Annals of DAAAM and Proceedings of 22nd DAAAM Symposium, November 23-26, 2011. Vienna: 1193-1194. Go to original source...
    9. Mikuš R., Balla J., Žernovič M., 2006. Formovanie tvaru ostria spevneného tvrdou vrstvou počas opotrebenia. [Formation of blade shape strengthen by hard layer during wear process.] In: Intertribo: tribologické problémy v exponovaných trecích sústavach: IX. medzinárodné sympózium. [Tribological Problems in Exposed Friction Systems: IX. International Symposium.] Bratislava, Kongres Management s.r.o: 119-123.
    10. Pulc V., Hrnčiar V., Gondár E., 2004. Náuka o materiáli. [Material Science.] Bratislava, Slovak University of Technology in Bratislava: 333.
    11. STN 41 2050, 1976. Oceľ 12 050. [Steel 12 050.] Bratislava, Slovak Office of Standards, Metrology and Testing.
    12. STN 41 5230, 1977. Oceľ 15 230 Cr-V. [Steel 15 230 Cr-V.] Bratislava, Slovak Office of Standards, Metrology and Testing. Go to original source...
    13. Tolnai R., Čičo P., 2001. Oteruvzornosť návarových materiálov novej koncepcie. [Wear resistance of hardfacing materials of a new concept.] Acta Technologica Agriculturae, 4: 99-102.
    14. Žitňanský J., Žarnovský J., 2005. Renovačné procesy a vplyv rezných podmienok. [Renovation processes and effect of cutting conditions.] In: Proceedings Quality and Reliability of Technical Systems, 13. Nitra: 184-187.

    This is an open access article distributed under the terms of the Creative Commons Attribution-NonCommercial 4.0 International (CC BY NC 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.


    Return to the content