Res. Agr. Eng., 2016, 62(3):99-105 | DOI: 10.17221/32/2015-RAE

Mechanical properties of composite material reinforced with textile waste from the process of tyres recyclingOriginal Paper

M. Müller
Department of Material Science and Manufacturing Technology, Faculty of Engineering, Czech University of Life Sciences Prague, Prague, Czech Republic

The paper deals with the polymeric fibre composite with the reinforcement on the basis of the waste from the process of the tyres recycling. The aim of the research was the use of the material of cleaned textile waste from the process of the tyres recycling. The secondary waste raw material was used as filler in the composite. The subject of performed experiments was the polymeric composite, whose continuous phase was in a form of a two-component epoxy adhesive (GlueEpox Rapid) and a discontinuous phase in a form of microfibers from the process of tyres recycling. The experiments results proved that the composite materials based on the textile waste from the process of the tyres recycling reached an increase of an impact strength, a tensile lap-shear strength and an elongation of the adhesive bond (to 2.5% vol.). The textile microfiller has a negative influence on the tensile strength and elongation of adhesives.

Keywords: epoxy resin; quality testing; microfiber; testing

Published: September 30, 2016  Show citation

ACS AIP APA ASA Harvard Chicago Chicago Notes IEEE ISO690 MLA NLM Turabian Vancouver
Müller M. Mechanical properties of composite material reinforced with textile waste from the process of tyres recycling. Res. Agr. Eng. 2016;62(3):99-105. doi: 10.17221/32/2015-RAE.
Share...
Download citation
  • BibTeX (.bib)
  • Bookends (.ris)
  • EasyBib (.ris)
  • EndNote (.enw)
  • EndNote 8 (.xml)
  • ISI WoS (.isi)
  • Medlars (.medlars)
  • Mendeley (.ris)
  • MODS (.xml)
  • Papers (.ris)
  • RefWorks (.txt)
  • RefManager (.ris)
  • RIS (.ris)
  • MS Word (.xml)
  • Zotero (.ris)
    • Open full article

    References

    1. Acevedo B., Fernández A.M., Barriocanal C. (2015): Identification of polymers in waste tyre reinforcing fibre by thermal analysis and pyrolysis. Journal of Analytical and Applied Pyrolysis, 111: 224-232. Go to original source...
    2. Bartl A., Hakl A., Mihalyi B., Wistuba M., Marini I. (2015): Recycling of fibres materials. Process Safety and Environmetal Protection, Trans IChemE, 83: 351-358. Go to original source...
    3. Èierna H., «avodová M. (2013): Using the design of experiment method to evaluate quality of cuts after cutting aluminum alloy by AWJ. Manufacturing Technology, 13: 303-307. Go to original source...
    4. Dadfar M.R., Ghadami F. (2013): Effect of rubber modification on fracture toughness properties of glass reinforced hot cured epoxy. Materials and Design, 47: 16-20. Go to original source...
    5. Fang Y., Zhan M., Wang Y. (2000): The status of recycling of waste rubber. Materials and Design, 22: 123-127. Go to original source...
    6. Ferreira C.T., Perez C.A.B., Hirayama D., Saron C. (2013): Recycling of polyamide (PA) from scrap tires as composites and blends. Journal of Environmental Chemical Engineering, 1: 762-767. Go to original source...
    7. Gaggino R., Positieri M.J., Irico P., Arguello R., Sánchez Amono M.P. (2014): Ecological roofing tiles made with rubber and plastic wastes. Advanced Materials Research, 844: 458-461. Go to original source...
    8. Hricova J. (2014): Environmentally conscious manufacturing: the effect of metalworking fluid in high speed machining. Key Engineering Materials, 581: 89-94. Go to original source...
    9. Kejval J., Müller M. (2013): Mechanical properties of multicomponent polymeric composite with particles of Al2O3/ SiC. Scientia Agriculturae Bohemica, 44: 237-242. Go to original source...
    10. Knapèíková L., Monka P., Hloch S. (2014): Composite Materials Reinforced with Fabric from Used Tyres. Journal of Manufacturing and Industrial Engineering, 12: 20-24.
    11. Novák M. (2011): Surface duality hardened steels after grinding. Manufacturing technology, 11: 55-59. Go to original source...
    12. Parres F., Crespo-Amorós J.E., Nadal-Gisbert A. (2009). Mechanical properties analysis of plaster reinforced with fiber and microfiber obtained from shredded tires. Construction and Building Materials, 23: 3182-3188. Go to original source...
    13. Xu S.A., Wang G.T., J., Mai Y.W. (2013): Effect of hybridization of liquid rubber and nanosilica particles on the morphology, mechanical properties, and fracture toughness of epoxy composites. Material Science, 48: 3546-3556. Go to original source...
    14. Taranu N., Banu D., Oprisan G., Budescu M., Bejan L. (2013): Strengthening of thin reinforced concrete slabs with composite strips. Romanian Journal of Materials, 43: 3-13.
    15. «avodova M. (2013): The surface quality of materials after cutting by abrasive water jet evaluated by selected methods. Manufacturing Technology, 13: 236-241. Go to original source...
    16. Valá¹ek P. (2014): Mechanical properties of epoxy resins filled with waste rubber powder. Manufacturing Technology, 14: 632-637. Go to original source...
    17. Valá¹ek P., Kejval J., Müller M. (2014): Epoxy resin filled with primary and secondary raw material - useable in agriculture. Research in Agricultural Engineering, 60: 165-171. Go to original source...
    18. Valá¹ek P., Müller M. (2014): EPDM rubber material utilization in epoxy composite systems. Agronomy Research, 12: 291-298.
    19. Weizhou J., Youzhli L., Guisheng Q. (2009): Studies on mechanical properties of epoxy composites filled with the grafted particles PGMA/Al2O3. Composites Science and Technology, 69: 391-395. Go to original source...

    This is an open access article distributed under the terms of the Creative Commons Attribution-NonCommercial 4.0 International (CC BY NC 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.


    Return to the content